You are here: Home » News » company news » Common faults and solutions of inflation head of aerosol filling machine

Common faults and solutions of inflation head of aerosol filling machine

Views: 0     Author: Site Editor     Publish Time: 2021-08-25      Origin: Site

Aerosol filling machine is the equipment used to fill aerosol products. The core components of the equipment are composed of liquid filling machine, aerator and sealing machine. Now aerosol products can be seen everywhere in our life. Aerosol filling machine has been applied to many industries, but some problems will inevitably occur after the aerosol filling machine equipment has been used for a long time, Today, the manufacturer of aerosol filling machine told you the common faults and solutions of the inflation head of aerosol filling machine. The following are the common faults and solutions of the inflation head of aerosol filling machine:

四合一气雾剂灌装机

Common fault I of aerosol filling machine inflation head:

The measurement accuracy is inaccurate during inflation. Cause analysis: the compressed air pressure is unstable and the seal in the metering cylinder is damaged. Solution: check and repair the air compressor; Replace the seal.


Common faults of aerosol filling machine inflation head II:

The inflation head of aerosol filling machine leaks during filling. Cause analysis: the rubber washer at the bottom of the inflation nozzle is damaged and the top pin of the inflation nozzle is not well lubricated. Solution: replace the rubber gasket; Properly add lubricating oil at the top tip.


Three common faults of aerosol filling machine inflation head:

When there is no filling, the inflation head leaks. Cause analysis: there are sundries on the Teflon gasket in the inflation head or the gasket is damaged; The sealing ring of the inflation head is damaged. Solution: remove sundries or replace gaskets or replace sealing rings.


Four common faults of aerosol filling machine inflation head:

The inflation head does not reset during filling and inflation of aerosol filling machine. Cause analysis: the throttle adjusting elbow on the small cylinder of the inflation head is adjusted too small or closed tightly, the platen of the inflation head is too high, the foot valve is bleeding, and the signal valve of the gas metering cylinder is bleeding. Solution: increase the throttle adjusting elbow of the inflation head, adjust the height of the platen, replace the foot valve and replace the signal valve.


Five common faults of aerosol filling machine inflation head:

When the foot valve is pressed, the inflation head will reset when it is not inflated or the inflation amount is very small after falling, the signal valve cylinder will reset without triggering, and the gas metering cylinder will not act. Cause analysis: the reset switch or signal valve has gas leakage. Solution: if there is slight air leakage, cut a small hole on the air pipe at the outlet end of the switch or signal valve. If it still cannot be solved, replace the reset switch or signal valve.


Common faults of aerosol filling machine inflation head 6:

Liquefied gas leaks from the middle exhaust hole of the gas metering cylinder, which has a special taste. Cause analysis: the Y-ring facing down on the base of the power cylinder is worn or deformed. Solution: replace the Y-ring.


Common faults of aerosol filling machine inflation head 7:

There is air leakage from the middle exhaust hole of the gas metering cylinder. Cause analysis: the Y-ring facing upward on the base of the power cylinder is worn or deformed. Solution: replace the Y-ring.


Common faults of aerosol filling machine inflation head 8:

The metering is adjusted to a large value, but the actual filling volume is very small. Cause analysis: the liquefied gas in the liquefied gas filling system is not liquid, but gaseous. Solution: change the output port of gas storage cylinder to liquid output port.


The above is the common faults and troubleshooting methods of aerosol filling head shared by aerosol filling machine manufacturers today. I believe you will know how to solve them after reading them.


PRODUCT CATEGORY

Shandong Finetry Machine Co. LTD.founded in 2003,
Iocated in Shandong province,China.We are an 
enterprise specializing in the research and.....

Quick Links

Product Center

 
 +86-0539-7702016
Phone Number : +86 13341277577 
Wechat & whatsapp:+86 13341277577
             finetrymachine@gmail.com
 
Contact us
Copyright © 2019 - 2021 Shandong Finetry Machine Co. LTD.